Home»Freightliner » Freightliner Business Class M2 Fault Codes List – Automated-Manual Transmissions
By |
1 Comment
See also:Freightliner Service Repair Manuals PDF
Freightliner Business Class M2
Transmission Faut codes list in PDF
Freightliner Business Class M2 Automated-Manual Transmissions Faut Codes (PDF)
Fault Code Guide (MID 130 SIDs)
SID | FMI | Text Message | Failure Reason |
18 | 02 | Prim Selector Erratic | The shift lever does not shift gears. |
33 | 03 | MultiPress Ind Short Hi | The hydraulic pressure sensor circuit is shorted to power. |
33 | 04 | MultiPress Ind Short Lo | The hydraulic pressure sensor circuit is shorted to ground. |
33 | 05 | MultiPress Ind OPEN | The hydraulic pressure sensor circuit is open. |
52 | 05 | Hydraulic Sys OPEN | The hydraulic pump circuit is open. |
52 | 07 | Hydraulic Sys NoRESPONSE | The hydraulic pressure does not increase even though the hydraulic pump is activated. |
52 | 11 | Clutch Act Not Known | The hydraulic pump temperature is too high. |
55 | 00 | Clutch Act HIGH | The clutch is too hot. |
55 | 07 | Clutch Act NoRESPONSE | The clutch does not operate properly. |
55 | 13 | Clutch Act Calibrate | The clutch needs to be calibrated. |
231 | 02 | SAE J1939 Datalink Erratic | The J1939 datalink is not communicating properly. |
231 | 09 | SAE J1939 Datalink UPDATE | The J1939 datalink has timed out. |
231 | 12 | SAE J1939 Datalink Bad | The J1939 datalink is not communicating with the transmission. |
251 | 00 | POWER SUPPLY HIGH | The power supply voltage is too high. |
251 | 01 | POWER SUPPLY Low | The power supply voltage is too low. |
251 | 05 | POWER SUPPLY OPEN | There is no power to the transmission with the engine running. |
251 | 14 | POWER SUPPLY RSRVD | The power supply is not properly grounded. |
253 | 02 | Calibration Memory Erratic | The transmission needs to be recalibrated. |
253 | 12 | Calibration Memory Bad | The transmission needs to be recalibrated. |
253 | 13 | Calibration Memory Calibrate | The transmission needs to be recalibrated. |
253 | 14 | Calibration Memory RSRVD | The transmission needs to be recalibrated. |
SID | FMI | Text Message | Failure Reason |
254 | 04 | Controller Short Lo | The TCU is shorted to ground. |
254 | 05 | Controller OPEN | The TCU has an open circuit. |
254 | 11 | Controller Not Known | The TCU AUTO mode software module has an error. |
254 | 12 | Controller Bad | The TCU has a hardware problem. |
254 | 13 | Controller Calibrate | The TCU has a software memory problem. |
Fault Code Guide (MID 130 PIDs)
PID | FMI | Text Message | Failure Reason |
33 | 02 | Erratic | The clutch position sensor gives invalid data. |
33 | 03 | Short Hi | The clutch position sensor circuit is shorted to power. |
33 | 04 | Short Lo | The clutch position sensor circuit is shorted to ground. |
33 | 05 | OPEN | The clutch position sensor circuit is open. |
33 | 14 | RSRVD | The clutch position sensor gives incorrect resistance readings. |
59 | 02 | Shift FNGR Gear Erratic | The shift rod position sensor gives invalid data. |
59 | 03 | Shift FNGR Gear Short Hi | The gear position sensor circuit is shorted to power. |
59 | 04 | Shift FNGR Gear Short Lo | The gear position sensor circuit is shorted to ground. |
59 | 05 | Shift FNGR Gear OPEN | The gear position sensor circuit is open. |
59 | 14 | Shift FNGR Gear RSRVD | The gear position sensor gives incorrect resistance readings. |
60 | 02 | Shift FNGR Rail Erratic | The rail position sensor circuit gives invalid data. |
60 | 03 | Shift FNGR Rail Short Hi | The rail position sensor circuit is shorted to power. |
60 | 04 | Shift FNGR Rail Short Lo | The rail position sensor circuit is shorted to ground. |
60 | 05 | Shift FNGR Rail OPEN | The rail position sensor circuit is open. |
60 | 14 | Shift FNGR Rail RSRVD | The rail position sensor gives incorrect resistance readings. |
64 | 09 | Dir Switch Update | The output shaft speed sensor is not providing accurate directional information. |
64 | 11 | Dir Switch Not Known | The output shaft speed sensor is not providing accurate directional information. |
158 | 00 | Volts (BattSw) HIGH | The voltage in the ignition power circuit is too high. |
158 | 01 | Volts (BattSw) Low | The voltage in the ignition power circuit is too low. |
161 | 02 | In shaft SPEED Erratic | The input shaft speed sensor circuit gives invalid data. |
161 | 03 | In shaft SPEED Short Hi | The input shaft speed sensor circuit is shorted to power. |
161 | 04 | In shaft SPEED Short Lo | The input shaft speed sensor circuit is shorted to ground. |
161 | 05 | In shaft SPEED OPEN | The input shaft speed sensor circuit is open. |
161 | 08 | In shaft SPEED Update | The input shaft speed sensor circuit is broadcasting an abnormal frequency. |
PID | FMI | Text Message | Failure Reason |
162 | 02 | RANGE Selected Erratic | The transmission is not properly calibrated. |
163 | 02 | RANGE Attained Erratic | The gears do not shift properly. |
191 | 02 | OUTPUT SPEED Erratic | One or both of the output shaft speed sensor circuits give invalid data. |
191 | 05 | OUTPUT SPEED OPEN | One or both of the output shaft speed sensor circuits are open. |
191 | 08 | OUTPUT SPEED SIGNAL | There is no signal coming from one or both output shaft speed sensors. |
191 | 14 | OUTPUT SPEED RSRVD | The output shaft speed sensor is providing invalid data. |
For a list of proprietary fault codes viewable on ServiceLink
AGS Proprietary Fault Codes (J1708) | |
Fault Code | Description |
3000109 | High voltage supply voltage—external (connector X1/12 and X1/15) |
3000113 | High voltage ignition key line—external (connector X1/9) |
3000209 | Low voltage supply voltage—external (connector X1/12 and X1/15) |
3000213 | Low voltage ignition key line—external (connector X1/9) |
3001210 | EEPROM parameter values error—internal |
3001510 | Clutch displacement control module parameter error—internal |
3001781 | Clutch calibration offset off limit—internal |
3002009 | Open load supply voltage—external (connector X1/12 and X1/15) |
3002016 | Open load/Short circuit VCC temperature sensor circuit board—internal |
3002017 | Open load/Short circuit VCC temperature sensor pump—internal |
3002116 | Short circuit GND temperature sensor circuit board—internal |
3002117 | Short circuit GND temperature sensor pump—internal |
3002214 | Short circuit VCC peripherals supply—external (connector X2/15) |
3003001 | EBC1 message timeout—external (J1939) |
3003101 | EEC1 message timeout—external (J1939) |
3003201 | EEC2 message timeout—external (J1939) |
3003301 | EEC3 message timeout—external (J1939) |
3003401 | ERC1 message timeout—external (J1939) |
3003501 | Wheel speed information message timeout—external (J1939) |
3003601 | CruiseControl (VCU) message timeout—external (J1939) |
3003701 | CruiseControl (bulkhead) message timeout—external (J1939) |
3003801 | Engine configuration message timeout—external (J1939) |
3003901 | Retarder configuration message timeout—external (J1939) |
3004001 | Component identification message timeout—external (J1939) |
3004101 | PTO information message timeout—external (J1939) |
3006101 | Incorrect engine data—external (J1939) |
3006201 | Timeout converted engine data for clutch module (low priority)—internal |
3006701 | Incorrect retarder data—external (J1939) |
3006801 | Incorrect ABS data—external (J1939) |
3006901 | Incorrect internal data—internal |
3007001 | Incorrect clutch module data—internal |
3007101 | Incorrect automated gear shift module data—internal |
3007201 | Incorrect internal data—internal |
3008881 | Clutch overload—internal |
3009280 | Plausibility error actual transmission gear ratio—internal |
3009710 | Test software—internal |
3009810 | Test electronic—internal |
AGS Proprietary Fault Codes (J1708) | |
Fault Code | Description |
3009910 | Test bench mode activated—internal |
3010390 | Automatic module: signal group cruise control / retarder—internal |
3010690 | Automatic module: signal output speed—internal |
3010790 | Automatic module: signal group MR—internal |
3010890 | Automatic module: signal group gear ratio—internal |
3010990 | Automatic module: learning values engine—internal |
3011081 | Plausibility error intended clutch position can not be reached within specified time—internal |
3011090 | Automatic module: learning values transmission—internal |
3011310 | Clutch calibration data missing/error—internal |
3011410 | Clutch parameter error—internal |
3011590 | Automatic module: signal group shifting time—internal |
3011690 | Automatic module: signal group ABS—internal |
3011790 | Automatic module: signal group pedal activation—internal |
3011890 | Automatic module: signal group lever—internal |
3011990 | Automatic module: error target system—internal |
3012014 | Open load peripherals supply—external (connector X2/15) |
3012019 | Plausibility error valve relay V-V2 on—internal |
3012035 | Open load power stage solenoid valve (clutch open 1)—internal |
3012036 | Open load power stage solenoid valve (clutch open 2)—internal |
3012037 | Open load power stage solenoid valve (clutch close 1)—internal |
3012038 | Open load power stage solenoid valve (clutch close 2)—internal |
3012050 | Open load speed sensor transmission output (DZ1)—external (connector X2/14) |
3012051 | Open load speed sensor transmission input—external (connector X2/11) |
3012052 | Open load speed sensor transmission output (D3)—external (connector X2/9) |
3012090 | Automatic module: system identification gearshift module—internal |
3012114 | Short circuit to GND peripherals supply—external (connector X2/15) |
3012118 | Plausibility error valve relay V-V1 off—internal |
3012119 | Plausibility error valve relay V-V2 off—internal |
3012136 | Short circuit GND power stage solenoid valve (clutch open 2)—internal |
3012138 | Short circuit GND power stage solenoid valve (clutch close 2)—internal |
3012151 | Short circuit GND speed sensor transmission input—external (connector X2/11 |
3012251 | Short circuit VCC speed sensor transmission input—external (connector X2/11) |
3012461 | Hydraulic level too low external—external |
3016201 | Timeout converted engine data for clutch module (medium priority)—internal |
3016401 | Timeout driving direction information—internal |
3016501 | Timeout internal communication shift module to clutch module (medium priority)—internal |
AGS Proprietary Fault Codes (J1708) | |
Fault Code | Description |
3018681 | Plausibility error clutch open request while inlet valves are closed—internal |
3018781 | Plausibility error clutch open request while outlet valves are closed—internal |
3019480 | Plausibility error driving direction—internal |
3019621 | SmartShift lever data invalid—external (connector X1/8, X1/11, X1/14) |
3019650 | Tooth signal interruption speed sensor transmission output (DZ1)—external (connector X2/14) |
3019651 | Tooth signal interruption speed sensor transmission input—external (connector X2/11) |
3019652 | Tooth signal interruption speed sensor transmission output (D3)—external (connector X2/9) |
3020110 | High voltage distance sensor supply—internal |
3020111 | Power supply high voltage—external (connector X3/1) |
3020210 | Low voltage distance sensor supply—internal |
3020211 | Power supply low voltage—external (connector X3/1) |
3021010 | Flash checksum error—internal |
3021110 | EEPROM calibration values error—internal |
3021610 | Clutch displacement offset failure—internal |
3022011 | Supply voltage open load—external (connector X3/1) |
3022012 | Open load GND connection—external (connector X1/18 and X1/21) |
3022015 | Open load pressure sensor signal—internal |
3022018 | Plausibility error valve relay V-V1 on—internal |
3022020 | Open load GND pump motor—external (connector X3/2) |
3022030 | Open load power stage solenoid valve (selection direction R)—internal |
3022031 | Open load power stage solenoid valve (selection direction 5/6)—internal |
3022032 | Open load power stage solenoid valve—internal |
3022033 | Open load power stage solenoid valve (gear direction 1,3,5)—internal |
3022034 | Open load power stage solenoid valve (pressure regulation)—internal |
3022041 | Open load distance sensor (gear)—internal |
3022042 | Open load distance sensor (selection)—internal |
3022044 | Open load distance sensor (clutch)—internal |
3022060 | Open loop power stage pump motor—internal |
3022115 | Short circuit GND pressure sensor signal—internal |
3022130 | Short circuit GND power stage solenoid valve (selection direction R)—internal |
3022131 | Short circuit GND power stage solenoid valve (selection direction 5/6)—internal |
3022132 | Short circuit GND power stage solenoid valve (gear direction R,2,4,6)—internal |
3022133 | Short circuit GND power stage solenoid valve (gear direction 1,3,5)—internal |
3022134 | Short circuit GND power stage solenoid valve (pressure regulation)—internal |
3022135 | Short circuit GND power stage solenoid valve (clutch open 1)—internal |
3022137 | Short circuit GND power stage solenoid valve (clutch close 1)—internal |
AGS Proprietary Fault Codes (J1708) | |
Fault Code | Description |
3022141 | Short circuit GND distance sensor (gear)—internal |
3022142 | Short circuit GND distance sensor (selection)—internal |
3022144 | Short circuit GND distance sensor (clutch)—internal |
3022160 | Short circuit GND power stage pump motor—internal |
3022215 | Short circuit VCC pressure sensor signal—internal |
3022241 | Short circuit VCC distance sensor (gear)—internal |
3022242 | Short circuit VCC distance sensor (selection)—internal |
3022244 | Short circuit VCC distance sensor (clutch)—internal |
3022317 | Over temperature power stage pump motor—internal |
3022590 | Automatic module: no signal vehicle speed—internal |
3022690 | Automatic module: signal group MR (high priority)—internal |
3022790 | Automatic module: signal group gear ratio (high priority)—internal |
3022890 | Automatic module: learning values engine (high priority)—internal |
3022990 | Automatic module: learning values transmission (high priority)—internal |
3024341 | Erratic distance sensor (gear)—internal |
3024342 | Erratic distance sensor (selection)—internal |
3024344 | Erratic distance sensor (clutch)—internal |
3024441 | Wrong coil resistance value distance sensor (gear)—internal |
3024442 | Incorrect coil resistance value distance sensor (selection)—internal |
3024444 | Incorrect coil resistance value distance sensor (clutch)—internal |
3024610 | Timeout displacement sensor value—internal |
3026001 | CAN bus off—external (connector X1/13 and X1/7) |
3026301 | Timeout converted engine data for clutch module (high priority)—internal |
3026501 | Timeout internal communication shift module to clutch module (high priority)—internal |
3027401 | No J1939 communication—internal / external (connector X1/13 and X1/7) |
3027501 | Timeout internal communication shift module to clutch module (high priority)—internal |
3028581 | Clutch displacement control failure—internal |
3029180 | No calculation of redundant transmission output speed—internal |
3029380 | Incorrect transmission type—internal |
3029580 | Plausibility error pressure build up—internal |
Related Posts
ECU 128 fault code on Freightliner Trucks
Freightliner Coronado Workshop, Repair and Maintenance Manuals PDF
Freightliner Columbia Workshop, Service and Owner’s Manuals PDF
Freightliner Century Workshop, Service and Owner’s Manuals PDF
Bernard njenga 24/11/2020
i have this codes that just popped up EUC128
5 1 d 254
no AbsP1 d 105
This is on a 2005 freightliner kindly advice if safe to continue driving. thanks in advance.Reply ↓